Each flowsheet prints as a drawing with a title block, followed by its stream table. To get a PDF, choose Save as PDF as the printer in the window that opens.
Units of measure
What every number is shown in, and what you type in. The choice is saved with the model. A single unit or stream can be shown in its own units: select it and open Units for this unit, or Units for this stream, at the bottom of its panel. Changing it converts what is on screen and changes no result. Scripts and the Reactions tab always work in the first unit of each list.
Export results
Every stream on every flowsheet, as solved now. The Excel workbook has four sheets: Streams, Units, Summary and, where streams carry a size distribution, Sizes. Values are numbers, not text, so you can calculate with them straight away.
Solver settings
Saved with the model. The solve repeats passes through the flowsheet, guessing each torn recycle stream, and updates every controller once per pass, until every tear variable and every controller setpoint is within tolerance for the set number of passes in a row.
The model as text
Saving to a file is the usual way, with Save and Open above. This is the same model as plain text, for pasting into an email or a chat. To load one, paste its text here and choose Load.
Build a flowsheet from scratch
Choose Clear flowsheet. On the Components tab, add what is in your ore and liquor.
On the Reactions tab, write each reaction and wait for the Balanced tag.
On the Flowsheet tab, add a Source / Sink / Link unit. It starts as a source: set its rate and composition. What it contains decides whether it is a slurry, a liquid or a gas.
Add the units: a Tank with Reactions ticked, then a Thickener or Filter, and a Source / Sink / Link unit set to Sink for every stream that leaves.
Connect them left to right. The flowsheet re-solves by itself after every change. Use Run, Step and Stop to watch the solver work through it.
Send an outlet back to an earlier unit to make a recycle. Add a Controller to hold a target.
Every action has several routes
Add a unit: drag it from the library, click it in the library, right-click empty canvas, or copy and paste.
Connect: drag a ringed port onto a unit, click the port then click the unit, right-click the unit, or use its Connections tab.
Disconnect: select the stream and press Delete, right-click the stream, drag its end dot onto empty canvas, or use the Connections tab.
Re-route: drag the stream's end dot to another unit, right-click the stream, or change Goes to in its panel.
Edit a unit: click it, double-click it, or right-click it.
Insert a unit into a stream: right-click the stream.
Blocks: tick Reactions, Heat loss, Evaporation, Addition or Removal on a tank to switch each on.
CCD: draw one thickener per wash stage, or right-click the canvas and choose Insert CCD train. Right-click a thickener to add a stage after it.
Following elements and components: on the Components tab, tick what to follow. The Flowsheet tab then shows how much of each was fed and what share reaches each sink.
Watch a run: Run steps the solver one pass round the flowsheet at a time so you can watch a recycle build up. Pause, Step and Stop work as you would expect, and Solve gives the finished answer at once.
Script: the Script tab sets unit settings from stream values, shows your own results and raises your own warnings.
Flipping a unit: select it and choose Flip left-right or Flip up-down, press H or V, or right-click it. Its inlet and outlets move to the other side and the streams follow.
Shaping a stream line: click a stream, then drag a small hollow handle on it to add a bend and pull the line up, down, left or right. In its panel choose right angles, free form or a straight line. Double-click a bend to remove it.
A bigger flowsheet: Bigger canvas uses the whole window for the drawing. The mouse wheel zooms, dragging empty space pans, and Fit shows everything.
Your own species: on the Components tab, add your own component. Give it a tag when it shares a formula with another, such as gold in ore and gold locked in ore. A reaction rate can also rise with a second component, such as carbon.
Particle size: tick Size distribution on a source and give its P80. Crushers and mills set a new size and report Bond power. Screens and cyclones split the solids by size.
pH and precipitation: tick Equilibrium on a tank and choose which solids may dissolve or precipitate. Stream pH then appears in the stream table, and a controller can hold a pH.
Cake washing: tick Washing on a filter. Inlets with no solids are the wash.
Heat exchanger: drop a stream on the upper or lower half to pick side A or side B.
Blocks that open: add a Flowsheet block. It gets its own flowsheet, and every open link inside becomes a port on the block. Double-click the block to step in, and use the trail above the canvas to step back out.
More flowsheets: choose + Flowsheet above the canvas. To carry a stream across, end it in a Link and join it to a Link on the other flowsheet. Each link keeps its own tag and shows the tag of the one it joins, as off-page connectors do on a drawing set. The stream number carries across. Double-click a link to jump to its other end.
Keyboard
CtrlZ undo, CtrlShiftZ redo
CtrlD duplicate, CtrlC and CtrlV copy and paste a unit
Delete removes the selected unit or stream
Arrow keys nudge the selected unit, with Shift for fine steps
CtrlEnter or F9 solves again
CtrlS saves the model to a file, CtrlO opens one, CtrlP prints the flowsheets and stream tables
Share of what was fed. Choose what to follow on the Components tab.
Recycle convergence
Components in this project
Follow through the flowsheet. Each ticked element or component gets a row in the table of where things end up.
Add from the library
The library holds formula, density, heat capacity and, for about half of its entries, the heat of formation at 25 °C. Molar mass comes from the formula. A dissolved salt or acid carries the heat of formation of its ions in dilute solution, and steam carries the value of liquid water because its heat of evaporation is already counted. Where the heat of formation is blank it is not known: type it in if a reaction needs it. For most solids and dissolved salts the heat capacity is an estimate made from the formula, and the density of a dissolved salt is an apparent value close to that of its dry crystal. Both can be edited in the table above once the component is added.
Add your own
About the property data
Molar mass is calculated from the formula. A component with no formula is inert and cannot take part in a reaction.
pH and solubility are calculated by PHREEQC from the U.S. Geological Survey. The MINTEQ data suits dilute to moderate solutions, and the SIT data from the ThermoChimie project reaches stronger ones. Very strong leach liquors and autoclave temperatures are indicative only. Heat of precipitation is not included.
Mill and crusher power is Bond's law across that unit, counting each inlet at its own P80. In a closed circuit it will not match the usual circuit figure from fresh feed to cyclone overflow exactly, so check it against that.
Each stream carries one size distribution for all its solids, on a fixed root-two sieve series, so P80 values are good to about 2%. Crushers, and mills on the Bond model, give a Rosin–Rammler product whatever the feed. Minerals do not grind at different rates. The population balance mill's default breakage values are generic, so calibrate them to test work.
Library densities and heat capacities are approximate handbook-style values entered from memory. Check them against your own source before relying on a result.
Dissolved salts use a single apparent density, so liquor densities are rough. Water gets less dense as it gets hotter, so volumes and g/L figures follow each stream's temperature. Gases and evaporated water leave a tank through its vent, the port on top. You can set the share of the gas that leaves that way; the rest stays in the outlets. Connect the vent to send them somewhere, or leave it open and they are counted as vented.
Dynamic run
Case study
Change one setting over a range and see what it does to the results. Each case is solved on a copy of the model, so the model itself is not changed.
1. The setting to change
2. The results to record
Results
How a case study works
The setting is any number on a unit or a reaction. It is given in the base units shown beside it, such as t/h, °C and kPa, whatever display units are chosen.
A setting only matters when it is in use. A tank temperature does nothing if the tank is adiabatic, and a rate does nothing if a controller or the script sets it. Those cases are marked in the Status column.
A second setting gives one line on the chart for each of its values, up to five.
Results can be stream values, unit values such as heat duty, plant results such as extraction, and anything the script shows.
Use this case writes that row's settings into the model.
The study set-up is saved with the model. The results are not: run it again after opening a file.
Energy balance
Where the heat comes from and where it goes, for the whole plant and for each unit. Every number is in kW. Anything the model cannot account for is shown in the last column.
How to check it by hand
Heat carried by a stream is counted from 0 °C: each component's flow × heat capacity × temperature, with water taken from the steam tables. Steam carries its heat of evaporation, so boiling shows up in the streams, not as a separate term.
Reaction heat is the heat of reaction on the Reactions tab × the amount reacted. Heat given off is on the In side; heat taken up is on the Out side.
For each unit: streams in + additions + heating + reaction heat + electrical heat = streams out + cooling + heat lost + other latent heat. The difference is the last column.
Click a row to see each stream's flow, temperature and heat, so the sums can be repeated on a calculator.
Power drawn by pumps, crushers and mills is listed but is not added to the streams: the model does not warm a stream by pumping or grinding. Electrowinning power is added when that option is ticked on the unit.
Not counted: heat from the equilibrium calculation (solubility and pH), and heats of mixing other than those written as reactions. A tank that uses the equilibrium block can show a small unexplained amount.
Script
One instruction per line. The script runs after every solve. If it changes a setting, the flowsheet is solved again until the settings stop moving.
What you can write
Set a unit setting:"Mill water".rate = 1.15 * S4.solids
Keep a value for later lines:feed = S1.solids
Show a result with the other results:show "Energy, kWh/t" = "Ball mill".kw / feed
Raise a warning:warn "Overflow is too coarse" if S7.P80 > 90
Stream values: total, solids, liquid (t/h), pctsolids, T, P, vol (m³/h), pH, P80, P50 (µm). Also flow(S1,"CuO") in t/h, conc(S3,"H2SO4") in g/L and passing(S7,75) in %.
Sums: + - * / ^, brackets, comparisons, and, or, not, and min, max, abs, sqrt, exp, ln, log, if(test, a, b). A # starts a comment.
Names in this project
Reactions
How reactions are applied
Write reactants -> products with a space each side of every plus sign, for example 2 FeS2 + 7 O2 + 2 H2O -> 2 FeSO4 + 2 H2SO4. Every species must be in the component list.
An unbalanced reaction is switched off so it cannot break the mass balance.
In a reactor, the ticked reactions run in the order listed, tank by tank. Each is capped by whichever reactant runs out first.
Kinetic mode is first order in the key reactant for a stirred tank, with the rate constant given at 60 °C. Fixed mode converts a set share of the key reactant across the whole train.